indentation

常见例句

• The operation was successful. The cheek indentation was now just barely noticeable.
  手术很成功, 左边脸上原来那块凹处简直看不见了.
• Indentation methods of hardness testing comprise two principal groups.
  压痕法测定硬度包括两大类.
• In OCR, an indentation in a stroke.
  使用光符阅读器(OCR)时, 笔划上的弯钩.
• In OCR, an indentation in a stroke.
  使用光符阅读器(OCR)时, 笔划上的弯钩.
• The amount of indentation needed in pixels.
  缩进量,需要用像素为单位.
• You cannot use indentation in combination with other tags, as box or code.
  缩进标记不能和其他标记组合使用, 例如框体或者代码.
• Complete of wood fiber, Processing method Aqueous, one surface smooth, Another surface is grid indentation.
  完全的木质纤维, 湿法加工, 一面光滑, 一面网痕.
• Objective : To study the appearance of the cadaver temporomandibular joint ( TMJ ) discs under confining indentation.
  目的: 研究离体环境下人体颞下颌关节盘的抗力表现.
• The correct method of measuring the indentation diameter, d, is shown in the figure.
  正确测量凹口直径的方法如图所示.
• Even if the lines ins are initially indented differently, this recipe makes their indentation homogeneous.
  既使各行原先的缩进不同, 这个配方也会使它们的缩近变得一致.
• Indentation is used to make corrugated board to operate as they design requirements into folding.
  不抬痕的功用是使瓦楞纸板不妨按照安插给求折叠不败箱.
• The operation was successful. The cheek indentation was now just barely noticeable.
  手术很成功, 左边脸上原来那块凹处简直看不见了.
• Indentation in source code is 3 blank characters.
  在原始码内缩排通常是3个空白字元.
• By adjusting the die and mould penetrated the changing indentation descend.
  通过调整凹模和凸模之间的间隙,即可改变压痕的深浅.
• Every found macro to expand will add an additional indentation level inside the trace output.
  每一个找到的要展开的宏都会在跟踪输出中增加一级缩入.
• When the pain slowly become 1 : heart bottom and can't also fix forever with of indentation.
  当痛苦慢慢地成为 1: 心脏底部,并且不可能永远也固定与凹进.
• When defining an indentation different from 0, the position of tabulation is not considered.
  任何不是零的缩进的位置将被忽略.
• Indent comment at the same level of indentation as the code you are documenting.
  注释缩进和其注释的代码在同一层次.
• The nano indentation hardness can be achieved by these curves, images and corresponding calculating method.
  通过载荷-压深曲线和压痕形貌图,以及相应的计算方法,可以得到纳米压痕硬度.
• Indentation section of a module to use simple, convenient.
  压痕条模的使用方法简单 、 方便.
• Its shape can be a square or circular wooden rod, to shoot is suitable for indentation.
  它的轮廓可以是不方形木条或不方形梢棒, 给适分于不抬出槽洋.
• In printing, it is the resistance of materials such ad rubber blanket, paper, etc, to indentation.
  在印刷方面是指胶布 、 纸张等物料对压凹的抗力.
• A shallow notch, cut , or indentation on a surface.
  表面上的较浅的刻槽 、 刻痕或缺口.
• The correct method of measuring the indentation diameter, d, is shown in the figure.
  正确测量凹口直径的方法如图所示.
• A split or indentation between two parts, as of the chin.
  两部分间(如下巴)的裂隙或凹口.
返回 indentation